935 replies to this topic

[HUBBA.HUBBA]

Sorry for late reply - find attached pics of my cubs wiring 
 
DSC08447 by Anglia305e, on Flickr
 
DSC08448 by Anglia305e, on Flickr
 
If you need more let me know - the wires to the back follow the line of the fuel pipe and through the N/S box section to the rear lights.

Thanks for that

[HUBBA.HUBBA]

Bought a few things from himley today. One of them being 3 x union jacks( for left, right and rear). Thought British army vehicles have them so why not
 20180513_194242.jpg   47.46K   1 downloads

[HUBBA.HUBBA]

Never realised there was a difference on the rocker tower geometry between standard and 1.5 roller tip. Always thought it was just the rockers. It didn't dawn on me until I saw the rocker tips nearly on the valves!
 20180518_171107.jpg   58.96K   0 downloads  20180518_171513.jpg   33.76K   0 downloads

[HUBBA.HUBBA]

Got cracking on the engine today. I would normally advocate not puttingvtge charger on before it goes into the bay but the cub has loads of room and a removable front

 20180519_161900.jpg   64.01K   7 downloads  20180519_161854.jpg   67.68K   9 downloads  20180519_161846.jpg   58.1K   7 downloads  20180519_161840.jpg   65.26K   2 downloads

Edited by HUBBA.HUBBA, 19 May 2018 - 06:17 PM.

[Archived2]

Sexy!

[panky]

I dribbled

[nicklouse]

sorry, but i would remove the wrapping.

[HUBBA.HUBBA]

sorry, but i would remove the wrapping.

Why? Need to keep bay temp down

[nicklouse]

 

sorry, but i would remove the wrapping.

Why? Need to keep bay temp down

 

promote rust. cause welds to crack. heat shield the carb. duct cold air into the carb.

[HUBBA.HUBBA]

Ready to take delivery
 20180526_114537.jpg   46.8K   0 downloads  20180526_114541.jpg   60.02K   0 downloads

The eagle has landed

 20180526_165909.jpg   60.01K   0 downloads

Had to persuade the inner CV joint/pot off the drive shaft the only way I know

 20180526_123312.jpg   53.58K   0 downloads

[HUBBA.HUBBA]

Here's an easy one. What am I making this evening?  20180530_194833.jpg   52.14K   0 downloads

[xrocketengineer]

Here's an easy one. What am I making this evening? 20180530_194833.jpg

Wine bottle rack?

[HUBBA.HUBBA]

This how it started.  20180530_171708.jpg   53.72K   0 downloads

Had to trim the bottom off as the massive wheels would have fouled it.

 20180530_202052.jpg   46.15K   1 downloads  20180530_202124.jpg   35.42K   1 downloads  20180530_205515.jpg   54.73K   1 downloads  20180530_205529.jpg   54.78K   1 downloads
All I Need to do now is tidy up the edges and spay it. Can't decide on colour, bmc green, Sandy or black. There's alot of green in there already, would say Sandy but it's not actually attached to the body. Suppose black would make it look like part of the radiator.
 20180530_214433_resized_1.jpg   62.24K   0 downloads

Edited by HUBBA.HUBBA, 30 May 2018 - 08:53 PM.

[Archived2]

That’s a good idea! Nice one

[HUBBA.HUBBA]

I bought a boost gauge which I intend to customise (of course!). Just wondered if this looks right. It's a cheapo TIM one, surely the needle should be sitting on zero! I bought an old TIM gauge prior to this one to take apart and that one had the needle in the same place Too!!?? Anyone had any experience with these?
 20180531_151436.jpg   38.01K   5 downloads