324 replies to this topic

[thelegg]

made a start on my fuel lines

 

 

But had to pack up quick as had a phone call to say I could drop my shafts off at the engineering place so fingers crossed I'll have some drive shafts soon :) also might be treating myself to a nice inlet manifold from fusion fabrication

Edited by thelegg, 31 October 2017 - 04:33 PM.

[thelegg]

Finally got the right length belt for my alternator 3rd time lucky :)

 

 

Almost finished my fuel lines but didn't have enough braided/rubber pipe for joining it to the tank

 

 

Should have my drive shafts in about 2 weeks and my inlet manifold should be here within 4 weeks so it's become abit of a waiting game

Edited by thelegg, 31 October 2017 - 04:38 PM.

['Chop']

Looking good Ryan. Wondered why you were a bit quiet...... Then found this thread. Tooks ages to catch up! Nice work

[thelegg]

Looking good Ryan. Wondered why you were a bit quiet...... Then found this thread. Tooks ages to catch up! Nice work

Cheers mate long time no see, you going to the next mania meet ?

[thelegg]

Not done much this evening but got my exhaust all painted up

 

Edited by thelegg, 31 October 2017 - 04:39 PM.

['Chop']

 

Looking good Ryan. Wondered why you were a bit quiet...... Then found this thread. Tooks ages to catch up! Nice work

Cheers mate long time no see, you going to the next mania meet ?

 

Hopefully yes. Missed mania but went to Rusteez that week instead!!

[thelegg]

Looking good Ryan. Wondered why you were a bit quiet...... Then found this thread. Tooks ages to catch up! Nice work

Cheers mate long time no see, you going to the next mania meet ?

Hopefully yes. Missed mania but went to Rusteez that week instead!!

Who else was there ?

[thelegg]

Hey guys quick question am I right in thinking I need an in line fuel filter on my feed pipe going to the engine ?

['Chop']

 

 

 

Looking good Ryan. Wondered why you were a bit quiet...... Then found this thread. Tooks ages to catch up! Nice work

Cheers mate long time no see, you going to the next mania meet ?

Hopefully yes. Missed mania but went to Rusteez that week instead!!

Who else was there ?

 

Me, Dave and Wendy!! the usual

Sometimes Colin and maybe Ben turn up....

[Shingler4596]

Hey guys quick question am I right in thinking I need an in line fuel filter on my feed pipe going to the engine ?

you may as well fit one. It won't be too hard and will save a lot of hastle in the future!

Edited by Shingler4596, 25 February 2016 - 01:51 PM.

[thelegg]

And so it begins!

 

Edited by thelegg, 31 October 2017 - 04:40 PM.

[thelegg]

IT'S ALIVE!

well it turns over haha

[EccentricToast]

Well done! Keep us updated on how you run the electrics be interested to see how you get on.

[thelegg]

Will do, I've connected up the main earth for the loom and now when the ignition is on I have an oil light, air bag light and the battery light on which is normal, the engine light is flashing but that's probably because it has stuff missing and no oil or coolant :) when ignition is off the nats LED light is flashing like it should so I'd say we're moving in the right direction 👍

Welded on some brackets and mounted the ECU on the inside of the bulkhead, now I just need to secure all the fuse boxes n relays

Edited by thelegg, 28 February 2016 - 09:07 PM.

[thelegg]

Ok so chopped loads more out of the loom most of which was just shortening it

 

 

Started getting more wires into there rough positions but think I'll remove all the central locking wires next as I have decided I won't ever use it

 

Edited by thelegg, 31 October 2017 - 04:42 PM.