Jump to content


Photo
- - - - -

What Size Tubing? [Bleeding Brakes.]


  • Please log in to reply
9 replies to this topic

#1 RawlinsGTR

RawlinsGTR

    Formally known as Dog

  • Members
  • PipPipPipPipPipPipPip
  • 1,046 posts
  • Location: Sevenoaks, Kent

Posted 14 September 2011 - 09:59 PM

Hi all,

I'm going to be bleeding my front brakes once I've replaced the calipers, and I was wondering;

Does anyone know the correct size tubing that will fit over the bleed nipples and not let any air in? This is on a stock 8.4" caliper.

This might have already been answered, but I couldn't find it anywhere :)

Thanks,

Simon.

#2 mike.

mike.

    Crazy About Mini's

  • Members
  • PipPipPipPipPipPipPipPipPipPip
  • 6,176 posts

Posted 14 September 2011 - 10:18 PM

You'll probably end up bleeding the rears a bit too, which have different sized nipples. To be honest, even if the tubing is a fair bit too small you can usually force it on anyway.

I'd say about 4mm internal diameter is about right to get a tight fit.

#3 jaydee

jaydee

    Crazy About Mini's

  • Members
  • PipPipPipPipPipPipPipPipPipPip
  • 8,565 posts

Posted 14 September 2011 - 10:28 PM

I've never 'tubed' bleeding nipples (on a mini).

#4 Ryang556

Ryang556

    Up Into Fourth

  • Members
  • PipPipPipPipPipPipPipPipPip
  • 2,747 posts
  • Location: Worcestershire
  • Local Club: Top Mini

Posted 14 September 2011 - 10:28 PM

I ended up just finding old tube from somewhere, mike is probably about right though, I had bigger bleed nipples on the rear drums so I just put another piece of tube in boiling water and forced it on to make a tight fit. :proud:

#5 RawlinsGTR

RawlinsGTR

    Formally known as Dog

  • Members
  • PipPipPipPipPipPipPip
  • 1,046 posts
  • Location: Sevenoaks, Kent

Posted 15 September 2011 - 06:51 AM

Great, thanks Ryan and Mike.

Jaydee - what did you do to bleed them then, if you didn't use a tube?

Thanks,

Simon.

#6 jaydee

jaydee

    Crazy About Mini's

  • Members
  • PipPipPipPipPipPipPipPipPipPip
  • 8,565 posts

Posted 15 September 2011 - 09:34 AM

Open spanner and an assistant pressing the pedal. Never had air back in the system.
I can see the need of a tube if rear lines are full of air so you cant bleed them, and you'll use a tube to suck oil from a can and prime the tubes.

#7 Ryang556

Ryang556

    Up Into Fourth

  • Members
  • PipPipPipPipPipPipPipPipPip
  • 2,747 posts
  • Location: Worcestershire
  • Local Club: Top Mini

Posted 15 September 2011 - 09:44 AM

Great, thanks Ryan and Mike.

Jaydee - what did you do to bleed them then, if you didn't use a tube?

Thanks,

Simon.


The main reason why I used a tube was on the end into a brake fluid bottle so I didn't lose it all over my drive ;)

#8 jaydee

jaydee

    Crazy About Mini's

  • Members
  • PipPipPipPipPipPipPipPipPipPip
  • 8,565 posts

Posted 15 September 2011 - 09:46 AM

Good point if you're working on your drive ryan!

#9 Ryang556

Ryang556

    Up Into Fourth

  • Members
  • PipPipPipPipPipPipPipPipPip
  • 2,747 posts
  • Location: Worcestershire
  • Local Club: Top Mini

Posted 15 September 2011 - 09:48 AM

Good point if you're working on your drive ryan!


Saves you putting your hand in your pocket to buy some more fluid as well! ;D

#10 jaydee

jaydee

    Crazy About Mini's

  • Members
  • PipPipPipPipPipPipPipPipPipPip
  • 8,565 posts

Posted 15 September 2011 - 10:22 AM

To be honest i wouldnt reuse old dot4..




1 user(s) are reading this topic

0 members, 1 guests, 0 anonymous users