What Did You Do To Your Mini Today
Started by
Ipod
, Apr 10 2010 07:06 PM
9650 replies to this topic
#2461
a_woolhouse
-
- Members
-
- 993 posts
One Carb Or Two?
- Location: Up inth hiills
Posted 30 December 2012 - 08:54 PM
Took the drivers side ball joint off! (MOT Time)
#2462
nosbigkin
-
- Noobies
-
- 60 posts
Stage One Kit Fitted
- Location: Hornchurch
Posted 30 December 2012 - 09:08 PM
Managed to un-do the EXTREMELY tight castle nut allowing us to remove the front discs
(And also managed to bend two wheel studs in the process)
(And also managed to bend two wheel studs in the process)
Edited by nosbigkin, 30 December 2012 - 09:10 PM.
#2463
Badboytunes
-
- Members
-
- 1,615 posts
Camshaft & Stage Two Head
- Location: Northampton
- Local Club: MINIS Unleashed
Posted 30 December 2012 - 10:40 PM
Took a pic of the car as it is minus her engine
#2464
Mrpeanut
-
- Members
-
- 1,019 posts
One Carb Or Two?
- Location: Southampton
- Local Club: Wessex MOC
Posted 01 January 2013 - 01:45 PM
Put fuel in it and drove it!
#2465
minirage
-
- Members
-
- 165 posts
Mini Mad
- Location: berkshire
Posted 01 January 2013 - 01:52 PM
nothing.... just think about it and go shopping at minispares
#2466
Ipod
-
- Members
-
- 2,024 posts
Up Into Fourth
Posted 01 January 2013 - 01:59 PM
looked at how to remove the side windows on my mpi, ready for tiniting 
And booked fella in to fit new front and rear window seals for tomorrow
And booked fella in to fit new front and rear window seals for tomorrow
#2467
minirage
-
- Members
-
- 165 posts
Mini Mad
- Location: berkshire
Posted 01 January 2013 - 03:21 PM
say whaaaaaa..... ya didnt fancy having a go at fitting them?looked at how to remove the side windows on my mpi, ready for tiniting
And booked fella in to fit new front and rear window seals for tomorrow
#2468
Ipod
-
- Members
-
- 2,024 posts
Up Into Fourth
Posted 01 January 2013 - 03:35 PM
say whaaaaaa..... ya didnt fancy having a go at fitting them?
looked at how to remove the side windows on my mpi, ready for tiniting
And booked fella in to fit new front and rear window seals for tomorrow
no, I have no fingers, and at £60 fitting I'd rather let someone with insurance F it up :)
#2469
Tamworthbay
-
- Members
-
- 7,025 posts
Crazy About Mini's
- Name: Clive
- Location: Tamworth
- Local Club: A5 minis
Posted 01 January 2013 - 03:42 PM
Took old dash old, played with fitting gt clocks and rev counter. Felt a Pratt when I tried to start the engine using the heater control as a choke.
#2470
minirage
-
- Members
-
- 165 posts
Mini Mad
- Location: berkshire
Posted 01 January 2013 - 04:48 PM
fair point, its still a mini adventure...................
say whaaaaaa..... ya didnt fancy having a go at fitting them?
looked at how to remove the side windows on my mpi, ready for tiniting
And booked fella in to fit new front and rear window seals for tomorrow
no, I have no fingers, and at £60 fitting I'd rather let someone with insurance F it up :)
#2471
miniman267
-
- Noobies
-
- 452 posts
Speeding Along Now
- Location: bath
- Local Club: mendip minis
Posted 01 January 2013 - 04:56 PM
fitted the side panel to my mini and took door step sill off along with sill
#2472
Andi-p
-
- Members
-
- 188 posts
Mini Mad
- Location: Darlington
Posted 03 January 2013 - 09:39 PM
Stripped my 998 motor to get ready for the machine shop to see if my engine is salvageable. Hope to build a twin cam 8 valve motor on throttle bodies.
#2473
harryh733
-
- Members
-
- 220 posts
Mini Mad
- Location: Norfolk
- Local Club: Norfolk Mini Owners Club
Posted 03 January 2013 - 11:34 PM
I spent some time today staring at my mini wishing my student loan would hurry up so I can give it a service and get it running nicely for the spring! I haven't driven it since July and I miss it!
#2474
colinu
-
- TMF+ Member
-
- 517 posts
Super Mini Mad
- Location: Santa Rosa, California USA
- Local Club: MOASF
Posted 04 January 2013 - 03:15 AM
Slapped two coats of POR15 on her belly.
#2475
peter-b
-
- Members
-
- 773 posts
One Carb Or Two?
- Location: Central Coast of NSW
- Local Club: still looking
Posted 04 January 2013 - 09:15 AM
Started making a 'roll over' jig to do body work. 12mths since starting rebuild.........almost half way.. WOOHOO!
3 user(s) are reading this topic
0 members, 3 guests, 0 anonymous users
